How much does it cost to repipe a house?

Repiping an entire home typically runs $2,000–$15,000, with most homeowners spending around $7,500. By square footage, that works out to roughly $1–$8 per sq ft — PEX pipe lands at the low end, copper at the high end, with the number of fixtures and how hard the pipes are to reach moving it in between.

PEX vs. copper — which costs less to repipe with?

PEX costs meaningfully less than copper, both for the pipe itself (roughly $0.40–$2 per linear foot vs. $2–$8 for copper) and for labor, since it's flexible enough to snake through existing walls without opening them up as much. Copper lasts longer and resists bacteria and UV better, but most residential repipes today use PEX because the price gap is significant on a whole-house job.

Why is labor most of the repiping cost, not the pipe itself?

Labor typically runs about 70% of a repiping bill. The material — a few hundred to a couple thousand dollars in pipe — is a small piece next to the time it takes to access pipes behind walls, under floors, or in a slab, run the new lines, pressure-test the system, and patch up whatever had to be opened.

Do I need a permit to repipe a house?

In most areas, yes — a whole-house repipe changes plumbing that inspectors need to verify, and permits typically run $50–$500 depending on your city. A licensed plumber usually pulls the permit as part of the job and schedules the required inspection.

How do I know if my house needs to be repiped?

Watch for discolored or rusty water, a noticeable drop in water pressure, recurring leaks you keep patching, or pipe older than 50 years — especially galvanized steel, lead, or polybutylene, none of which are considered safe or worth repairing long-term. A plumber can inspect the accessible pipe to confirm before you commit to a full repipe.

Whole-house repipe cost in Denver

Whole-house repipe in Denver costs about $2,100 to $15,800 (typically $7,900) — local prices run about 5% above the national average.

These figures adjust our national whole-house repipe range to Denver's local cost level — see the method and sources below.

Low

$2,100

Typical

$7,900

High

$15,800

About $1.05 – $8.40 per sq ft of home, installed

How we localized this

We start from our national whole-house repipe range of $2,000–$15,000 and adjust it for Denver, where costs run about 5% above the national average. Denver home-improvement costs run modestly above the U.S. average. A cost-index comparison puts Denver renovation pricing about 12% above the national average in its overall framing, while the multiplier it actually applies to individual project estimates is closer to 4% above; other local renovation guides put the metro at 10–20% above. Mortenson's quarterly construction cost index also shows Denver's nonresidential construction costs rising faster than the national pace, consistent with a tight, in-demand contractor market. We land on a conservative 5% above national, nearer the lower end of that range. Materials are priced roughly nationally, so treat this as an approximation — your actual price depends on your home, contractor, and project specifics.

Denver cost sources (2)

Denver Home Improvement Costs (2026) — Cost to Renovate
Construction Cost Index for Denver — Mortenson

A decade of rapid population growth has kept Denver's contractor market tight, and material transport costs into the Rocky Mountain region add a modest premium on top of labor. The Front Range sits in one of the country's top hail-exposure zones, which makes roofing and exterior-siding work a recurring, often insurance-driven expense. Denver's semi-arid, high-altitude climate also affects concrete work — flatwork tends to crack faster than in humid climates without fiber reinforcement and properly placed control joints, so that's worth confirming with a contractor on any driveway, patio, or foundation job. Most Denver homes have full, unfinished basements, which makes basement finishing one of the metro's most common and highest-return projects.

Estimate your Denver whole-house repipe

Estimate by home size, pipe material, and access. The estimate starts from our published per-square-foot range.

Your area

Adjusts the estimate to local cost levels. Pick a metro or leave on national.

Home size: 2,000 sq ft

Pipe material

Pipe accessibility

Pipes under a slab or behind finished walls take far longer to reach than an open crawlspace or basement.

Additional work

Estimated cost for your options in Denver

$2,100 – $16,800

Typical: $7,900

Adjusted for Denver — costs there run about 5% above the national average.

How we got this

Starts from our published whole-house repipe range (per sq ft × 2,000), adjusted for:

Pipe material: PEX (most common today)×1
Pipe accessibility: Open access (crawlspace/basement)×1
Additional work: Repipe only×1
Area: Denver×1.05

These figures are planning estimates compiled from public cost data on the dates shown — not quotes, bids, or guarantees. Real prices vary widely with your home, location, materials, permits, and contractor. Always get itemized written quotes from licensed local pros before budgeting or hiring.

What changes the price

Home size — Raises cost
More square footage means more fixtures and longer pipe runs — repiping is priced mainly by the size of the home.
Pipe material — Varies
PEX is the least expensive and most common choice today; CPVC costs a bit more, and copper runs several times more for the same job.
Accessibility — Raises cost
Pipes reachable through a crawlspace or basement are far cheaper to replace than pipes under a concrete slab, behind finished walls, or on upper floors.
Number of fixtures — Raises cost
Each sink, toilet, shower, and appliance connection adds its own run and labor time.
Drywall & wall repair — Raises cost
Opening walls or floors to reach old pipes means patching them afterward, often billed separately from the plumbing work itself.
Permits & inspection — Raises cost
Most jurisdictions require a permit and inspection for a whole-house repipe, built into a licensed plumber's quote.

Get real quotes for your Denver whole-house repipe

Our ranges are for planning. The only way to know your real price is itemized quotes from licensed local pros — always get at least three before you hire.

Tip: search for licensed, insured Denver whole-house repipe contractors in your area, check reviews and references, and compare written itemized bids — not just bottom-line numbers.

Whole-house repipe cost — FAQ

How much does it cost to repipe a house?: Repiping an entire home typically runs $2,000–$15,000, with most homeowners spending around $7,500. By square footage, that works out to roughly $1–$8 per sq ft — PEX pipe lands at the low end, copper at the high end, with the number of fixtures and how hard the pipes are to reach moving it in between.
PEX vs. copper — which costs less to repipe with?: PEX costs meaningfully less than copper, both for the pipe itself (roughly $0.40–$2 per linear foot vs. $2–$8 for copper) and for labor, since it's flexible enough to snake through existing walls without opening them up as much. Copper lasts longer and resists bacteria and UV better, but most residential repipes today use PEX because the price gap is significant on a whole-house job.
Why is labor most of the repiping cost, not the pipe itself?: Labor typically runs about 70% of a repiping bill. The material — a few hundred to a couple thousand dollars in pipe — is a small piece next to the time it takes to access pipes behind walls, under floors, or in a slab, run the new lines, pressure-test the system, and patch up whatever had to be opened.
Do I need a permit to repipe a house?: In most areas, yes — a whole-house repipe changes plumbing that inspectors need to verify, and permits typically run $50–$500 depending on your city. A licensed plumber usually pulls the permit as part of the job and schedules the required inspection.
How do I know if my house needs to be repiped?: Watch for discolored or rusty water, a noticeable drop in water pressure, recurring leaks you keep patching, or pipe older than 50 years — especially galvanized steel, lead, or polybutylene, none of which are considered safe or worth repairing long-term. A plumber can inspect the accessible pipe to confirm before you commit to a full repipe.

Cost data compiled July 26, 2026.

Sources (3)

How Much Does It Cost to Repipe a House? [2026 Data] — Angi
How Much Does It Cost to Install or Replace Plumbing? (2026) — HomeGuide
How Much Does It Cost to Repipe a House in 2025? — HomeAdvisor

National range and per-sq-ft unit synthesize Angi, HomeGuide, and HomeAdvisor into one low–typical–high band rather than reproducing any single source's table. HomeAdvisor's own headline 'Normal Range' widget on this article ($372–$2,119, avg $1,246) directly contradicts its own per-square-foot body table on the same page (~$4.50/sq ft, i.e. $9,000+ for a 2,000 sq ft home) — read as a template/data mismatch on their end and NOT used; their per-square-foot table was used instead. Labor (~70% of the bill per both Angi and HomeAdvisor) is the dominant cost driver, not the pipe material. Metro-level breakdowns are coming as we verify local data.

Compare other locations

See all Denver plumbing costs on the Denver plumbing page.

↑